How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
We have stumbled upon the article involving Installing A Bathtub directly below on the net and concluded it made sense to write about it with you on my blog.
Setting up a bath tub isn't specifically rocket science, however it does need solid plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a new one is also a reasonably challenging project. If the old bathtub is conveniently easily accessible, the project can move easily; if you need to open a wall surface to get rid of the old tub and place the new bathtub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will require an assistant to leave the old tub and embeded in the brand-new one. Make certain you have certified on your own for the task as well as are comfortable trying it. As opposed to employing a professional to take over a halfway-completed task, it is much better to think about employing one prior to you start. Possibilities are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your restroom if you have actually currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your tools and also material checklist need to comprise the following:
Preparing for the Installment
Firstly, the sustaining framework supplied with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the remaining water that will originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before going on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little points.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest versatile faucet connector to the ideal supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and brand-new pipework for leakages and tighten them if needed. Fill the tub and likewise check the overflow electrical outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the supplier's user's manual. Tiling and securing around the bathtub ought to wait till the bathtub has actually been used a minimum of when as this will resolve it into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the tap in position with the manufacturer provided backnut. When the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind needs to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about complications with moisture as well as possible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealer can split rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently offered on the market. It is a good idea to fit the tiles using waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that report about Tools You Need to Install a New Bathtub from a good friend on our other site. Do you know about someone else who is curious about the subject? Feel free to share it. I enjoy reading our article about Tools You Need to Install a New Bathtub .
View Website Report this page